[<<Erster] [<zurück] [weiter>] [Letzter>>] 16 Artikel in dieser Kategorie

Q12X, F5J-400 Segler, Rot, Bausatz mit Carbon Rumpf

329,90 EUR
(inkl. 20% MwSt. zzgl. Versand)
 
Artikeldatenblatt drucken
Art.Nr.: Q12X
Lieferzeit: 3-5 Tage 3-5 Tage
F5J Modell Q12
F5J Modell Q12
F5J Modell Q12
F5J Modell Q12
F5J Modell Q12
F5J Modell Q12
Der Q12X ist die Weiterentwicklung des Q12. Noch leichter und mit Carbonrumpf.  Er profitiert von der langjährigen Erfahrung des Hersteller Horejsi mit DLG Modellen. Der Flügel ist als leichter Schaumkern mit GFK beschichtet und mit Kohlefaser verstärkt aufgebaut. Ebenso das Leitwerk. Der Rumpf ist auf wenig Widerstand optimiert, aber er bietet genug Platz für Motor, Akku und Fernsteuerung. Das Modell ist für die Wettbewerbsklasse F5J-400 bestens geeignet.

Achtung! Die Abbildung weicht vom verkauften Modell ab ( weisser GfK Rumpf).


Technische Daten
  • Spannweite: 2000mm
  • Länge: ca: 1210mm
  • Profil: AG 40, 41, 42, 43
  • Gesamtgewicht flugfertig: ab ca 530g
  • Motorempfehlung; Dualsky XM2826EA-10
  • Prop: 10x6
  • Akkuempfehlung: 2S/1200mAh LiXX
Gewicht
  • Tragfläche (Links u. Rechts): ca. 190g
  • SLW: ca. 7g
  • HLW: ca. 14g
  • Rumpf: ca. 65g
  • Kleinteile: ca. 26g
Lieferumfang
  • Tragflächenhälften, Befestigung bereits eingebaut
  • Rumpfvorderteil, Carbon
  • Rumpfrohr
  • Seiteneitwerk
  • Höhenleiterk
  • Kleinteile
Es sind keine elektronischen Komponenten und keine Kleinteile im Lieferumfang enthalten. Der Bau des Modells erfordert einiges an Erfahrung und Geschick.


---------

The EP glider Q12 is the new version of our very successful Q10 and its successors.

The Q12  takes use from our long-years experience with DLG models. The gliders, made with the foam/skin technology, flew much better, than those stick and film types. The main reason was seemingly the overall improvement of aerodynamic properties.
The foam/skin design provides much higher rigidity. The A/R can be very high. The ailerons and brakes will not warp. The A/R is about same as that of free flight power models.
Each half of the wing is made as single part. The dihedral is built in during the molding process.

Except for the wing, all other parts are similar to the Q11.

 
The pod was designed to be used for many different types of models and equipment. It is long such, that folding prop up to 14" diameter could be used. The pod is very slick, yet it provides enough room for RC and power unit parts. The bottom is a bit flattened to get even more room inside the pod.

The rear fuselage part consists of carbon/glass boom. It provides rather long tail arm for better flight stability.

The tail feathers are made in similar method as the wings. They are very lightweight.

The CG is in correct position even with the very lightweight power unit components.

The on-board RC system is normally supplied from the ESC's BEC. If the current demands of your system is higher, you can use VR-3 voltage controller. It is supplied from the battery ballance connector. We have never had any problems with this power supply type.


X